A GOOD START

Cutting plan examples

Fourteen projects to open, understand and make your own. Each example is produced by the same calculation that plans your project.

1D · Lumber shelf frame10 / 10 parts
2×4 stud, 8 ft 1 · 96 in1 · Upright441 · Upright447 3/496 in
✓ Geometry independently validated10 cuts

Lumber shelf frame

Four 8 ft 2×4 studs are enough for the four uprights and six rails of a shelf frame. The example shows how parts of different lengths share boards of equal length.

Open in planner →
1D · Small tube frame8 / 8 parts
Steel tube, 10 ft 1 · 120 in1 · Leg3622422422411 1/2120 in
✓ Geometry independently validated8 cuts

Small tube frame

Three 10 ft steel tubes for a small frame with four legs and four braces. A typical case for metal tubing with a fixed kerf.

Open in planner →
1D · Mixed-length baseboards6 / 6 parts
Baseboard, 8 ft 1 · 96 in1 · Living room wall673226 3/496 in
✓ Geometry independently validated6 cuts

Mixed-length baseboards

Baseboards from mixed lengths: 8 ft and 6 ft boards are combined so the wall, hallway and alcove need as little extra as possible.

Open in planner →
2D · Plywood shelving6 / 6 parts
Plywood sheet 4×8 1 · 96 × 48 in1 · Side panel40 × 121 · Side panel40 × 122 · Shelf24 × 1224 × 11 5/815 7/8 × 23 3/42 · Shelf24 × 122 · Shelf24 × 122 · Shelf24 × 1224 × 11 5/831 3/4 × 4896 in48 in
✓ Geometry independently validated9 cuts

Plywood shelving

A simple shelf from one 4 × 8 ft plywood sheet: two side panels and four shelves with straight, saw-ready cuts.

Open in planner →
2D · Grain-matched decorative panel4 / 4 parts
Veneered panel 1 · 80 × 40 in1 · Door →36 × 161 · Door →36 × 1636 × 7 3/42 →24 × 162 →24 × 1624 × 7 3/419 3/4 × 4080 in →40 in
✓ Geometry independently validated6 cuts

Grain-matched decorative panel

Doors and drawer fronts from a veneered panel whose grain must run lengthwise. Rotation is locked so every front matches.

Open in planner →
2D · Offcuts and limited stock5 / 5 parts
Offcut 1 · 28 × 20 in1 · Back panel26 × 1826 × 1 7/828 in20 in
✓ Geometry independently validated8 cuts

Offcuts and limited stock

Tight stock: one sheet and an existing offcut. The example shows how offcuts are used and what happens when it gets tight.

Open in planner →
2D · Kitchen base cabinet7 / 7 parts
Plywood sheet 4×8 1 · 96 × 48 in1 · Side30 × 231 · Side30 × 232 · Bottom22 1/2 × 2334 × 22 1/234 × 22 1/25 · Door29 3/4 × 23 3/44 · Shelf22 1/2 × 2143 1/2 × 2196 in48 in
✓ Geometry independently validated11 cuts

Kitchen base cabinet

A 24 in kitchen base cabinet box from ¾ in plywood: sides, bottom, two stretchers, a shelf and the door fit on one 4 × 8 ft sheet. The bottom sits between the sides, so it is two thicknesses narrower.

Open in planner →
2D · Two-door wardrobe9 / 9 parts
Plywood sheet 4×8 1 · 96 × 48 in1 · Side72 × 161 · Side72 × 164 · Door71 3/4 × 14 3/4216 × 19 3/896 in48 in
✓ Geometry independently validated16 cuts

Two-door wardrobe

A 6 ft tall, 30 in wide wardrobe with two doors and three shelves from two plywood sheets. Long parts such as the sides and doors drive the layout here.

Open in planner →
1D · Raised garden bed16 / 16 parts
Cedar 2×6, 12 ft 1 · 144 in172233233144 in
✓ Geometry independently validated16 cuts

Raised garden bed

A 6 × 3 ft raised garden bed with four rows of cedar 2×6. Four of the eight 12 ft boards yield one long side board and two short ones, the other four one long side board and a long offcut, because two 6 ft boards do not fit on one board once you allow for the kerf. The short boards are two thicknesses shorter because they sit between the long sides.

Open in planner →
1D · Workbench frame12 / 12 parts
2×4, 10 ft 1 · 120 in1 · Leg34 1/21 · Leg34 1/2323323120 in
✓ Geometry independently validated12 cuts

Workbench frame

The frame of a 60 × 30 in workbench from 2×4s: four legs, four long rails and four short rails. The top is a separate sheet and not part of the linear cut list.

Open in planner →
1D · Deck boards from two lengths14 / 14 parts
Deck board, 16 ft 1 · 192 in1 · Board row901 · Board row90192 in
✓ Geometry independently validated14 cuts

Deck boards from two lengths

Deck boards for a 90 in deep deck from 16 ft and 12 ft boards. The example shows how two stock lengths are combined and which offcuts remain for fascia or steps.

Open in planner →
2D · Plywood shoe rack7 / 7 parts
Plywood sheet 4×8 1 · 96 × 48 in1 · Side36 × 121 · Side36 × 12230 1/2 × 123 · Shoe shelf30 1/2 × 11230 1/2 × 123 · Shoe shelf30 1/2 × 113 · Shoe shelf30 1/2 × 1130 1/2 × 13 5/829 1/4 × 4896 in48 in
✓ Geometry independently validated10 cuts

Plywood shoe rack

A shoe rack 36 in tall, 32 in wide and 12 in deep from ¾ in plywood with three shoe shelves. The shelves sit between the sides and are 1 in shallower so the toes of the shoes have room. Everything fits on one 4 × 8 ft sheet.

Open in planner →
2D · Entryway bench with coat panel6 / 6 parts
Plywood sheet 4×8 1 · 96 × 48 in1 · Coat panel40 × 3640 × 11 7/82 · Seat40 × 165 · Hat shelf40 × 12317 1/4 × 16317 1/4 × 16415 × 9 3/896 in48 in
✓ Geometry independently validated11 cuts

Entryway bench with coat panel

An entryway bench with a coat panel from ¾ in plywood: a 40 × 36 in panel for hooks, a hat shelf and a bench with seat, two sides and a shoe shelf, all from one 4 × 8 ft sheet. The bench sides are shorter by the seat thickness so the bench ends up 18 in high.

Open in planner →
2D · TV stand with two doors9 / 9 parts
Plywood sheet 4×8 1 · 96 × 48 in5 · Door5 · Door1 · Top and bottom48 × 151 · Top and bottom48 × 152 · Side2 · Side14 5/8 × 1534 · Shelf22 7/8 × 144 · Shelf22 7/8 × 1433 3/8 × 1496 in48 in
✓ Geometry independently validated13 cuts

TV stand with two doors

A TV stand 48 in wide, 18 in high and 15 in deep with a center divider, two shelves and two overlay doors from one 4 × 8 ft sheet of ¾ in plywood. Top and bottom run through, the sides sit between them.

Open in planner →
1D · Aluminum T-slot frame12 / 12 parts
T-slot extrusion, 8 ft 1 · 96 in2 · Long rail452 · Long rail455 3/496 in
✓ Geometry independently validated12 cuts

Aluminum T-slot frame

A 48 × 24 × 32 in frame from 1.5 in aluminum T-slot extrusion, for a workbench or a printer enclosure: four legs plus four long and four short rails from 8 ft bars. The rails are two profile widths shorter because they sit between the legs. Two legs and a short rail share one bar, so five bars are enough.

Open in planner →
2D · Plywood desk4 / 4 parts
Plywood sheet 4×8 1 · 96 × 48 in1 · Desk top60 × 23 3/43 · Modesty panel58 1/2 × 1258 1/2 × 122 · Side panel28 3/4 × 23 3/42 · Side panel28 3/4 × 23 3/47 × 4896 in48 in
✓ Geometry independently validated7 cuts

Plywood desk

A desk 60 in wide and 29½ in high from ¾ in plywood: top, two side panels and a modesty panel fit on one 4 × 8 ft sheet. The desk is 23¾ in deep instead of 24 in, because two 24 in parts plus the kerf do not fit across a 48 in sheet. The sides are one thickness shorter because the top sits on them.

Open in planner →