Example · Sheet cutting

Plywood desk

A desk 60 in wide and 29½ in high from ¾ in plywood: top, two side panels and a modesty panel fit on one 4 × 8 ft sheet. The desk is 23¾ in deep instead of 24 in, because two 24 in parts plus the kerf do not fit across a 48 in sheet. The sides are one thickness shorter because the top sits on them.

Open and edit in the planner

Free · No sign-up needed · Your data stays with you

Stock piece 1 / 1
Plywood sheet 4×8 1 · 96 × 48 in1 · Desk top60 × 23 3/43 · Modesty panel58 1/2 × 1258 1/2 × 122 · Side panel28 3/4 × 23 3/42 · Side panel28 3/4 × 23 3/47 × 4896 in48 in

Result

  • 4 / 4 Parts placed
  • 1 Stock piece
  • 7 cuts
  • 75.8 % Material use
  • 0.26 ft² Saw loss
  • 58 1/2 × 12 in largest offcut

✓ Geometry independently validated

Your stock

  • Plywood sheet 4×8: 1 × 96 × 48 in · Available stock

Parts to cut

  • Desk top: 1 × 60 × 23 3/4 in
  • Side panel: 2 × 28 3/4 × 23 3/4 in
  • Modesty panel: 1 × 58 1/2 × 12 in

Rules

  • Material group: Plywood · 3/4 in
  • Saw kerf: 1/8 in
  • Edge trim: 0 in
  • Grain axis: No constraint
  • Allow 90° rotation: yes

Cutting sequence · Stock piece 1

  1. Piece 96 × 48 in: vertical cut 60 in from the left edge. Leaves 60 × 48 in and 35 7/8 × 48 in; kerf 1/8 in.
  2. Piece 60 × 48 in: horizontal cut 23 3/4 in from the top edge. Leaves 60 × 23 3/4 in and 60 × 24 1/8 in; kerf 1/8 in.
  3. Piece 60 × 24 1/8 in: vertical cut 58 1/2 in from the left edge. Leaves 58 1/2 × 24 1/8 in and 1 3/8 × 24 1/8 in; kerf 1/8 in.
  4. Piece 58 1/2 × 24 1/8 in: horizontal cut 12 in from the top edge. Leaves 58 1/2 × 12 in and 58 1/2 × 12 in; kerf 1/8 in.
  5. Piece 35 7/8 × 48 in: vertical cut 28 3/4 in from the left edge. Leaves 28 3/4 × 48 in and 7 × 48 in; kerf 1/8 in.
  6. Piece 28 3/4 × 48 in: horizontal cut 23 3/4 in from the top edge. Leaves 28 3/4 × 23 3/4 in and 28 3/4 × 24 1/8 in; kerf 1/8 in.
  7. Piece 28 3/4 × 24 1/8 in: horizontal cut 23 3/4 in from the top edge. Leaves 28 3/4 × 23 3/4 in and 28 3/4 × 1/4 in; kerf 1/8 in.

Sheet cutting optimizer →